FOUNDRY of Bells. The metal, it is to be observed, is different for bells, from what it is for statues; there being no tin in the statue-metal: but there is a fifth, and sometimes more, in the bell-metal.
The dimensions of the core and the wax for bells, if a ring of bells especially, are not left to chance, but must be measured on a scale, or diapason, which gives the height, aperture, and thickness, necessary for the several tones required.
It is on the wax that the several mouldings and other ornaments are formed to be represented in relievo, on the outside of the bell.
The business of bell-foundry is reducible to three particulars. 1. The proportion of a bell. 2. The forming of the mould; and, 3. The melting of the metal.
The proportions of our bells differ much from those of the Chinese: in ours, the modern proportions are, to make the diameter fifteen times the thickness of the brim, and twelve times the height.
There are two kinds of preparations, viz. the simple and the relative: the former are those proportions only that are between the several parts of a bell, to render it sonorous; the relative proportions establish a requisite harmony between several bells.
The particulars necessary for making the mould of a bell are, 1. The earth: the most cohesive is the best; it must be well ground and sifted, to prevent any chinks. 2. Brick-stone; which must be used for the mine, mould, or core, and for the furnace. 3. Horse-dung, hair, and hemp, mixed with the earth, to render the cement more binding. 4. The wax for inscriptions, coats of arms, &c. 5. The tallow equally mixed with the wax, in order to put a slight lay of it upon the outer mould, before any letters are applied to it. 6. The coals to dry the mould.
For making the mould, they have a scaffold consisting of four boards, ranged upon tressels. Upon this they carry the earth, grossly diluted, to mix it with horse-dung, beating the whole with a large spatula.
The compasses of construction is the chief instrument for making the mould, which consist of two different
Foundery. ferent legs joined by a third piece. And last of all, the founders shelves, on which are the engravings of the letters, cartridges, coats of arms, &c.
They first dig a hole of a sufficient depth to contain the mould of the bell, together with the case, or cannon, under ground; and about six inches lower than the terreplain, where the work is performed. The hole must be wide enough for a free passage between the mould and walls of the hole, or between one mould and another, when several bells are to be cast. At the centre of the hole is a stake erected, that is strongly fastened in the ground. This supports an iron peg, on which the pivot of the second branch of the compasses turns. The stake is encompassed with a solid brick-work, perfectly round, about half a foot high, and of the proposed bell's diameter. This they call a mill-stone. The parts of the mould are, the core, the model of the bell, and the shell. When the outer surface of the core is formed, they begin to raise the core, which is made of bricks that are laid in courses of equal height upon a lay of plain earth. At the laying of each brick, they bring near it the branch of the compasses, on which the curve of the core is shaped, so as that there may remain between it and the curve the distance of a line, to be afterwards filled up with layers of cement. The work is continued to the top, only leaving an opening for the coals to bake the core. This work is covered with a layer of cement, made of earth and horse-dung; on which they move the compasses of construction, to make it of an even smoothness every where.
The first layer being finished, they put the fire to the core, by filling it half with coals, through an opening that is kept shut, during the baking, with a cake of earth that has been separately baked. The first fire consumes the stake, and the fire is left in the core half or sometimes a whole day: the first layer being thoroughly dry, they cover it with a second, third, and fourth; each being smoothed by the board of the compasses, and thoroughly dried before they proceed to another.
The core being completed, they take the compasses to pieces, with intent to cut off the thickness of the model, and the compasses are immediately put in their place to begin a second piece of the mould. It consists of a mixture of earth and hair, applied with the hand on the core, in several cakes that close together. This work is finished by several layers of a thinner cement of the same matter, smoothed by the compasses, and thoroughly dried before another is laid on. The first layer of the model is a mixture of wax and grease spread over the whole. After which are applied the inscriptions, coats of arms, &c. besmeared with a pencil dipped in a vessel of wax in a chaffing-dish: this is done for every letter. Before the shell is begun, the compasses are taken to pieces, to cut off all the wood that fills the place of the thickness to be given to the shell.
The first layer is the same earth with the rest, sifted very fine; whilst it is tempering in water, it is mixed with cow's hair, to make it cohere. The whole being a thin cullis, is gently poured on the model, that fills exactly all the sinuities of the figures, &c. and this is repeated till the whole is two lines thick over the model. When this layer is thoroughly dried, they
cover it with a second of the same matter, but some-
Foundery. what thicker: when this second layer becomes of some consistence, they apply the compasses again, and light a fire in the core, so as to melt off the wax of the inscriptions, &c.
After this, they go on with other layers of the shell, by means of the compasses. Here they add to the cow's hair a quantity of hemp, spread upon the layers, and afterwards smoothed by the board of the compasses. The thickness of the shell comes to four or five inches lower than the mill-stone before observed, and surrounds it quite close, which prevents the extravasation of the metal. The wax should be taken out before the melting of the metal.
The ear of the bell requires a separate work, which is done during the drying of the several incrustations of the cement. It has seven rings; the seventh is called the bridge, and unites the others, being a perpendicular support to strengthen the curves. It has an aperture at the top, to admit a large iron peg, bent at the bottom; and this is introduced into two holes in the beam, fastened with two strong iron keys. There are models made of the rings, with masses of beaten earth, that are dried in the fire, in order to have the hollow of them. These rings are gently pressed upon a layer of earth and cow's hair, one half of its depth; and then taken out, without breaking the mould. This operation is repeated 12 times for 12 half-moulds, that two and two united may make the hollows of the six rings: the same they do for the hollow of the bridge, and bake them all, to unite them together.
Upon the open place left for the coals to be put in, are placed the rings that constitute the ear. They first put into this open place the iron-ring to support the clapper of the bell; then they make a round cake of clay, to fill up the diameter of the thickness of the core. This cake, after baking, is clapped upon the opening, and folded with a thin mortar spread over it, which binds the cover close to the core.
The hollow of the model is filled with an earth, sufficiently moist to fix on the place, which is strewed at several times upon the cover of the core; and they beat it gently with a pestle, to a proper height; and a workman smooths the earth at top with a wooden trowel dipped in water.
Upon this cover, to be taken off afterwards, they assemble the hollows of the rings. When every thing is in its proper place, they strengthen the outside of the hollows with mortar, in order to bind them with the bridge, and keep them steady at the bottom, by means of a cake of the same mortar, which fills up the whole aperture of the shell. This they let dry, that it may be removed without breaking. To make room for the metal, they pull off the hollows of the rings, through which the metal is to pass, before it enters into the vacuity of the mould. The shell being unloaded of its ear, they range under the millstone five or six pieces of wood, about two feet long, and thick enough to reach almost the lower part of the shell; between these and the mould, they drive in wooden wedges with a mallet, to shake the shell of the model whereon it rests, so as to be pulled up and got out of the pit.
When this and the wax are removed, they break the model and the layer of earth, through which the metal must run, from the hollow of the rings, between
The furnace has a place for the fire, and another for the metal. The fire-place has a large chimney with a spacious ash-hole. The furnace which contains the metal, is vaulted, whose bottom is made of earth, rammed down; the rest is built with brick. It has four apertures; the first, through which the flame vibrates; the second is closed with a stopple that is opened for the metal to run; the others are to separate the dross, or scoria, of the metal by wooden rakes: through these last apertures passes the thick smoke. The ground of the furnace is built sloping, for the metal to run down.
FOUNDRY of Great Guns and Mortar-Pieces. The method of casting these pieces is little different from that of bells: they are run massy, without any core, being determined by the hollow of the shell; and they are afterwards bored with a steel trepan, that is worked either by horses or a water-mill.
For the metal, parts, proportions, &c. of these pieces, see GUNNERY.